There are many Frigidaire oven error codes and they have different meanings. If you want to know why your Frigidaire oven is showing an error code and what to do, this article is for you.
Table of Contents
Frigidaire Oven Error Code F045 — How To Fix
This Frigidaire oven error code indicates a problem with the cooling fan. To fix this issue, the cooling fan should be replaced. Follow the steps below to replace the cooling fan in a Frigidaire oven…
Step 1: Pull the oven away from the wall.
Step 2: Unplug the oven’s power cord from the outlet or switch the circuit breaker off.
Step 3: Take out the six screws which hold the upper back panel of the oven in place. Do this using a quarter inch nut driver.
Step 4: Remove the panel and set it aside.
Step 5: Disconnect the two wires connected to the cooling fan assembly.
Step 6: Open the door of the oven.
Step 7: Take out the screws under the stove top which secure it using a Philips head screwdriver. There will be two or three screws.
Step 8: Pull the stove top off and set it aside on a towel lined sturdy surface.
Step 9: Take out the four Philips head screws which hold the cooling fan assembly to the panel.
Step 10: Go to the oven’s rear and remove the cooling fan assembly.
Step 11: Get a new cooling fan assembly.
Step 12: Peel off the strips of foam from the old fan and stick them on the new one.
Step 13: Position the cooling fan motor on the oven.
Step 14: Hold the cooling fan in place with the four Philips head screws.
Step 15: Reposition the stove top on the oven and push it back.
Step 16: Return the screws underneath the stove top which hold it in place.
Step 17: Close the oven door.
Step 18: Reconnect the wires to the cooling fan assembly.
Step 19: Reposition the oven’s upper back panel and secure it with the six screws.
Step 20: Tighten the six screws using a quarter inch nut driver.
Step 21: Plug the oven back in or switch the circuit breaker back on.
Step 22: Push the oven back to the wall.
Also follow the steps above if you see the Frigidaire oven error code F47.
Watch the video below for a visual of how to replace the cooling fan assembly in a Frigidaire oven.
Frigidaire Oven Error Code F10 — How To Fix
If this error code appears on your oven, the temperature sensor or control board is faulty. Below we show you how to test and replace the temperature sensor in a Frigidaire oven…
Step 1: Pull the oven away from the wall.
Step 2: Unplug the power cord.
Step 3: Using a quarter inch nut driver, take out the screws which hold the oven’s upper rear panel in place. There should be six screws.
Step 4: Set the panel aside.
Step 5: Take out the screw under the oven’s lower rear panel on the left.
Step 6: Take out the other screws which hold the lower back panel in place.
Step 7: Set the panel aside.
Step 8: Disconnect the wire from the temperature sensor. The sensor is on the right side of the oven.
Step 9: Get a multimeter and turn it to the ohms setting.
Step 10: Touch the multimeter probes to the sensor wire connector. If the reading is lower than 1100 ohms or higher than 1300 ohms, the sensor is faulty and should be replaced.
Step 11: Take out the screws which hold the sensor in place.
Step 12: Remove the sensor and get a new one.
Step 13: Position the new sensor in the oven.
Step 14: Hold the sensor in place with the screws.
Step 15: Connect the wire plug to the sensor.
Step 16: Return the oven’s lower back panel and the screws which hold it in place.
Step 17: Also return the screw under it.
Step 18: Reposition the upper back panel and secure with the screws.
Step 19: Plug the oven back in or switch the circuit breaker on.
Step 20: Push the oven back to the wall.
Also follow the steps above if you see the Frigidaire oven error code F1, F3, F31 or F30.
Watch the video below for a visual of how to replace the sensor in a Frigidaire oven.
If the temperature sensor isn’t faulty, the control board should be replaced. Look at this article to replace the control board in a Frigidaire oven. Also read the article in the link if your Frigidaire oven shows the F15 error code or F68 error code.
Check out these articles…
Frigidaire Oven Element [Problems & Solutions]
How To Clean A Frigidaire Oven [Detailed Guide]
Frigidaire Oven Igniter [How To, Problems & Solutions]
Frigidaire Oven Is Not Working [Proven Solutions]
Frigidaire Oven Lock [Guide, Issues & Solutions]
Frigidaire Oven Error Code F50 — How To Fix
If you see this Frigidaire oven error code, reset the oven. If this doesn’t fix the problem, follow the steps below to replace the relay board in your Frigidaire oven.
Step 1: Switch off your oven’s circuit breaker.
Step 2: Pull the oven away from the wall.
Step 3: Take out the six screws which hold the oven’s lower back panel in place using a quarter inch nut driver.
Step 4: Also take out the other screw under the lower panel.
Step 5: Lift the panel off and set it aside.
Step 6: Note where each wire goes on the relay board. You should see the relay board on the right.
Step 7: Disconnect the wires connected to the relay board.
Step 8: Take out the three screws which hold the relay board to the oven using a Philips head screwdriver.
Step 9: Remove the relay board.
Step 10: Get a replacement.
Step 11: Secure the new relay board to the oven using the three Philips head screws.
Step 12: Reconnect the wires to the relay board making sure each one goes to the right place.
Step 13: Reposition the oven’s lower back panel.
Step 14: Hold the panel in place with the screws.
Step 15: Return the other screw underneath the panel.
Step 16: Push the oven back to the wall.
Step 17: Switch the circuit breaker back on.
The video below will walk you through the process of replacing the relay board in a Frigidaire oven.
Frigidaire Oven Error Code F11 — How To Fix
This Frigidaire oven error code indicates a problem with the keypad. To fix this problem, the touchpad should be replaced. Below we show you how to replace the touchpad of a Frigidaire oven…
Step 1: Switch off the circuit breaker.
Step 2: Pull the oven away from the wall.
Step 3: Take out the screws which hold the oven’s upper back panel in place with a quarter inch nut driver. There should be six screws.
Step 4: Set the oven’s upper back panel aside.
Step 5: Take out the screws which hold the control board to the oven.
Step 6: Peel off the touchpad from the control board.
Step 7: Get a new touchpad.
Step 8: Peel off the backing from the touchpad.
Step 9: Stick the new touchpad to the control board.
Step 10: Return the screws which hold the control board to the oven.
Step 11: Reposition the oven’s upper panel and secure with the screws.
Step 12: Switch your circuit breaker back on.
The video below will give you a visual of how to replace the touchpad of a Frigidaire oven.
Frigidaire Oven Error Code F14 — How To Fix
To fix this Frigidaire oven error code, follow the steps below…
Step 1: Unplug the oven’s power cord from the outlet.
Step 2: Take out the screws which secure the oven’s upper back panel using a quarter inch nut driver. There should be six screws.
Step 3: Set the panel aside.
Step 4: On the control board, there is a ribbon cable. Pull it out of the holder.
Step 5: Push the ribbon cable back into the holder.
Step 6: While holding the cable down, push the holder down to hold it in place.
Step 7: Return the upper back panel and the screws which hold it in place.
Step 8: Plug the oven’s power cord back in.
Also follow the steps above to fix the Frigidaire oven error code E014. If that doesn’t work, read the section above this one to replace your oven touchpad.
Frigidaire Oven Error Code F93 — How To Fix
This Frigidaire oven error code appears as the result of a faulty door lock motor. Below we have listed the steps for you to follow in order to replace the door lock motor in a Frigidaire oven…
Step 1: Pull the oven away from the wall.
Step 2: Unplug the oven’s power cord.
Step 3: Take out the screw under the oven’s lower back panel using a quarter inch nut driver.
Step 4: Using the same nut driver, take out the six screws which hold the lower back panel.
Step 5: Set the panel aside.
Step 6: Make a note of where each wire goes on the door lock motor then disconnect them.
Step 7: Take out the two screws securing the door lock motor to the oven using a quarter inch nut driver.
Step 8: Bend the motor back to release it from the rod.
Step 9: Get a new door lock motor.
Step 10: Position the rod in the door lock motor.
Step 11: Secure the door lock motor to the oven’s rear using the two screws.
Step 12: Connect all the wires to the door lock motor making sure each one goes to the right place.
Step 13: Reposition the back panel and return the six screws which hold it in place.
Step 14: Return the screw under the panel.
Step 15: Plug the oven back in.
Step 16: Push the oven back to the wall.
Also follow the steps above to fix the Frigidaire oven error code DR or F90.
The video below will give you a visual of how to replace the door lock motor in a Frigidaire oven.
How To Fix 5D Error Code On Frigidaire Oven
To fix this Frigidaire oven error code, follow the steps listed below…
Step 1: Unplug the oven’s power cord from the outlet.
Step 2: After 5 minutes, plug the oven back in.
Step 3: Press “Cancel”.
Step 4: Press “Oven light” and “Timer” simultaneously.
If this doesn’t fix the problem, read this article to replace your Frigidaire oven’s control board. Also read the article in the link to fix the Frigidaire oven error code sd.
Frigidaire Oven Error Code SF — How To Fix
This Frigidaire oven error code appears when there is a power failure. If your oven was still in sabbath mode when the power failure occurred, the SF error code will appear on the display. To fix this, you will need to turn off sabbath mode. To turn off sabbath mode on a Frigidaire oven, follow these steps…
Step 1: Make sure the oven is on.
Step 2: Hold down the “Bake Time” and “Clock” buttons simultaneously.
Step 3: Hold these buttons down for three seconds.
The video below talks about the sabbath mode feature in a Frigidaire oven.
PF Error Code On Frigidaire Oven — How To Fix
To fix this Frigidaire oven error code, follow these steps…
Step 1: Pull the oven away from the wall and unplug the power cord from the outlet.
Step 2: Leave the oven unplugged for at least 5 minutes.
Step 3: After 5 minutes, plug the oven back in.
Step 4: Turn the oven on and press the “Cancel” button.
Frigidaire Microwave Oven Error Code E-11 — How To Fix
To fix this Frigidaire microwave oven error code, the control panel will need to be replaced. Below are the steps for you to follow in order to replace the control panel of a Frigidaire microwave oven…
Step 1: Unplug the microwave’s power cord from the outlet.
Step 2: Open the microwave door.
Step 3: Take out the two screws which secure the microwave’s front vent using a Philips head screwdriver.
Step 4: Carefully pry off the front vent from the microwave using a putty knife.
Step 5: Set the vent aside.
Step 6: Take out the screw at the top of the control panel assembly which holds it in place.
Step 7: Lift the control panel up and lower it down.
Step 8: Make a note of where each wire goes on the control board. You could also take a picture to make it easier.
Step 9: Set the control panel assembly on a cloth lined surface.
Step 10: Take out the four screws which hold the control board to the control panel. Use a Philips head screwdriver to do this.
Step 11: Remove the control board by first disconnecting the ribbon cable from it.
Step 12: Using a flat head screwdriver, push back the tabs which hold the control board’s mounting plate on the control panel.
Step 13: Remove the plate.
Step 14: Get a new control panel.
Step 15: Position the plate on the control panel and snap it into place.
Step 16: Return the control board and secure it with the four Philips head screws.
Step 17: Reconnect the ribbon cable to the control board.
Step 18: Take the control panel assembly back to the microwave and connect the wires to it. Make sure each wire goes to the right place.
Step 19: Insert the tabs on the control panel into the slots in the microwave.
Step 20: Secure the control panel assembly to the microwave using the screw.
Step 21: Reposition the microwave’s front vent.
Step 22: Return the two screws at the top of the front vent which hold it in place.
Step 23: Close the door of the microwave.
Step 24: Plug the microwave’s power cord back into the outlet.
Watch the video below for a visual of how to replace the control panel of a Frigidaire microwave.