Do you want to know how to reset a Frigidaire oven? Well, in this article, we will show you how to reset a Frigidaire oven and more.
Table of Contents
How To Reset Frigidaire Oven Temperature
To reset the temperature of your Frigidaire oven, follow these steps…
Step 1: Open the oven door.
Step 2: Place a thermometer on the center rack.
Step 3: Close the oven door and set the oven to bake.
Step 4: Set the oven to 350 degrees F.
Step 5: Press the “Start” button.
Step 6: After 20 minutes, take out the thermometer and look at the reading. If the reading is higher or lower than the set temperature, the oven will need to adjusted accordingly.
Step 7: Hold “Bake” down for 3 seconds. If that doesn’t work, hold down the “Bake” and “Broil” buttons simultaneously for 3 seconds.
Step 8: Using the arrows or number pad, adjust the oven’s temperature.
Step 9: Press “Start” to save your setting.
Watch the video below for a visual of how to reset the temperature of your Frigidaire oven.
How To Reset A Frigidaire Oven After A Power Outage
To reset your Frigidaire oven after a power outage, follow these steps…
Step 1: Switch off the oven’s circuit breaker.
Step 2: Leave the circuit breaker off for 10 minutes.
Step 3: After 10 minutes, switch the circuit breaker back on.
How To Reset A Frigidaire Oven Clock
To reset your Frigidaire oven clock, follow the steps listed below…
Step 1: Unplug the oven from the outlet. You may need to pull the oven away from the wall to do so.
Step 2: Leave the oven unplugged for 5 minutes.
Step 3: After 5 minutes, plug the oven back in.
Step 4: Turn the oven on and press the “clock” button.
Step 5: Using the up and down arrows or the numbers on the oven’s control panel, input your desired time.
Step 6: Press “Start” to save the changes.
The video below will show you how to set a Frigidaire oven clock.
Check out these articles…
Frigidaire Oven Error Codes [Easy Fixes]
Frigidaire Oven Glass [How To, Issues & Solutions]
Frigidaire Oven Overheating [How To Fix]
Frigidaire Oven Burner [Issues & Solutions]
Frigidaire Oven Racks [How To, Issues & Solutions]
Frigidaire Oven F10 Reset
To reset the F10 error code on your Frigidaire oven, simply unplug the power cord for five minutes then plug it back in. If that doesn’t fix the issue, read this article to replace your Frigidaire oven’s temperature sensor.
Frigidaire Oven F13 Code Reset
To reset this error code on a Frigidaire oven, simply unplug the oven’s power cord for five minutes. Plug the oven back in after five minutes. If that doesn’t fix the problem, the control board should be replaced. If you would like to replace your Frigidaire oven’s control board yourself, do the following…
Step 1: Pull the oven away from the wall and unplug the power cord.
Step 2: Turn the oven around.
Step 3: Take out the six quarter inch screws which secure the oven’s upper back panel.
Step 4: Set the panel aside.
Step 5: Go to the oven’s front and take out the two screws under the control panel using a Philips head screwdriver. There will be one screw on each side.
Step 6: Place a towel on the stove top.
Step 7: Lift the control panel assembly and lower it down.
Step 8: Take out the four screws which hold the control board to the control panel using the Philips head screwdriver.
Step 9: Make a note of where each wire goes on the control board then disconnect them.
Step 10: Carefully peel off the overlay from the control board.
Step 11: Get a replacement board.
Step 12: Stick the overlay to the new board.
Step 13: Connect the wires to the control board. Make sure each wire goes to the right place.
Step 14: Reposition the control panel assembly on the oven frame.
Step 15: Return the two screws under the control panel assembly which secure it.
Step 16: Reposition the oven’s upper back panel.
Step 17: Hold the panel in place with the six quarter inch screws.
Step 18: Plug the oven back in.
Follow the steps above to replace your control board if your Frigidaire oven clock keeps resetting.
Watch the video below for a visual of how to replace the control board in a Frigidaire oven.
Frigidaire Oven Door Lock Reset
To reset a Frigidaire oven door lock, unplug the oven. Plug the oven back in after five minutes. If your oven door doesn’t open, the door lock is faulty. Some door lock motors are located on the oven’s rear while others are located at the front. We will show you how to replace these two door lock motors. To replace a front mounted door lock motor in a Frigidaire oven, follow these steps…
Step 1: Pull the oven away from the wall and unplug the power cord.
Step 2: Insert a coat hanger in between the stove top and oven door.
Step 3: Using the coat hanger, pull the door latch back to release the door.
Step 4: Open the oven door.
Step 5: Take out the screws under the stove top which hold it in place. If there are no screws, skip this step and go to the next one.
Step 6: Lift the stove top.
Step 7: If needed, hold the stove top with a thick piece of wood.
Step 8: Take out the screws which hold the metal plate covering the oven’s insulation.
Step 9: Lift the plate off.
Step 10: Note where each wire goes on the door lock motor or take a picture.
Step 11: Disconnect the wires from the door motor.
Step 12: Take out the two screws at the front of the oven which hold the door lock motor in place.
Step 13: Get a new door lock motor and connect the wires to it.
Step 14: Position it in the oven and hold it in place with the two screws.
Step 15: Return the metal plate and secure with the screws.
Step 16: Lower the stove top and return the screws which hold it in place.
Step 17: Close the oven door.
Step 18: Plug the oven back in.
To replace a Frigidaire oven rear mounted door lock motor, follow the steps listed below…
Step 1: Pull the oven away from the wall.
Step 2: Unplug the power cord from the outlet.
Step 3: Take out the screws which hold the oven’s lower back panel in place using a quarter inch nut driver.
Step 4: If there is a screw under the oven’s lower back panel, take it out as well.
Step 5: Lift the panel off and set it aside.
Step 6: Take a picture of the door lock motor to remember where each wire goes.
Step 7: Disconnect the wires from the door lock motor.
Step 8: Remove the two screws which hold the door lock motor in place using a socket or nut driver.
Step 9: Tilt the motor inward to remove it from the rod.
Step 10: To unlock the oven door, push the rod forward.
Step 11: Get a new door lock motor and position it on the rod.
Step 12: Hold the motor in place with the two screws.
Step 13: Connect the wires to the door lock motor. Use the picture you took for reference to ensure you connect the wires to the right places on the door lock motor.
Step 14: Reposition the oven’s back panel.
Step 15: Hold the panel in place with the screws.
Step 16: If you took out a screw under the panel, return it.
Step 17: Plug the oven back in.
Step 18: Return the oven to its usual position.
Watch the video below if you would like a visual of how to replace a Frigidaire oven front mounted door lock motor or rear mounted door lock motor.
Frigidaire Oven Control Board Reset
Below are the steps you need to follow in order to replace the control board in your Frigidaire oven…
Step 1: Pull the oven away from the wall.
Step 2: Disconnect the oven’s power cord from the outlet.
Step 3: Leave the oven unplugged for a few minutes.
Step 4: After a few minutes, plug the oven back in.
