Can you reset a Samsung microwave? Yes, you can. In this article we are going to walk you through the very simple steps you need to follow in order to reset your microwave.
Table of Contents
How to Reset a Samsung Microwave
To reset your Samsung microwave oven:
Step 1: Unplug the microwave from the outlet
Step 2: Leave the microwave unplugged for at least two minutes in order to reset it.
Step 3: Plug the microwave back.
Step 4: Once you have done this, try using the microwave like you normally do. If it now operates properly, then the reset was a success. However, if it doesn’t, the problem isn’t what can be fixed through resetting. You’ll need to contact a technician to find out what the issue is.
Reset Samsung Microwave Error Code
To reset the microwave when it shows an error code, do the following:
Step 1: Begin by unplugging the microwave
Step 2: If the error is showing because the microwave’s electronics are a bit wet, leave the microwave to dry.
Step 3: If moisture in the electronics isn’t a possibility, wait for 1 to 2 minutes.
Step 4: Afterwards, turn it back on and use as you normally do.
if it still doesn’t operate at all or how it used to, you should contact an experienced technician or your Samsung service center.
How Do You Reset the Filter on Samsung Microwave
To reset the filter on your Samsung microwave, do the following…
Step 1: Look underneath the microwave, there are two filters on each side.
Step 2: Next, take out the filters by pulling the tabs they have.
Step 3: Once you have done that, place the filters in a bowl and pour some hot water and dish-washing soap.
Step 4: Leave that to soak for 10 to 15 minutes.
Step 5: Afterwards, take the filters out and rinse them with clean water.
Step 6: Leave them to dry on a towel.
Step 7: Once they are dry, place them back in and resume using your microwave.
Important note: You don’t actually reset the filter in a microwave. When the “Filter” message pops up in a microwave’s display, it doesn’t mean there is a fault. It’s just a way of telling you that it is time to clean the filter. To stop the filter message from displaying, follow these easy steps outlined above for resetting the filter on your Samsung microwave.
The video below will walk you through how to replace a microwave filter.
How Do I Reset the Filter Light on Samsung Microwave?
To reset the filter light on your Samsung microwave, simply hold down the “0” button till the filter light clears. However, if you don’t clean the microwave filter before doing this, the message might pop up again.
Important note: The filter light is showing on your microwave because it needs to be cleaned. So you are advised to clean your filter first before resetting the filter light.
The video below will show you how to reset the filter light of a Samsung microwave.
Does a Samsung Microwave Have a Reset Button
No, it doesn’t. You reset a Samsung microwave by leaving it unplugged for 2 minutes.
Reset Time on Samsung Microwave
To reset the clock on your Samsung microwave, do the following:
Step 1: Begin by locating the clock button. This should be on the right side of the microwave’s control panel. However, if you can’t find it on the right side, look to the left side right underneath “power level.” You should see a tiny clock button.
Step 2: Hold down the clock button for 30 seconds.This will make the clock set option appear.
Step 3: After doing this, set the time by pressing the numbers on the microwave.
Step 4: Afterwards, press the clock button again to alternate between AM and PM.
Step 5: Once you have done this, press the start button to set the time.
The video below will show you how to set the time on a Samsung microwave clock.
Check out these articles…
How to Bake Pork Chops in the Oven [Detailed Guide]
Samsung Microwave Errors [Causes & Solutions]
Samsung Microwave Filter [How To]
How Do You Fix a Broken Samsung Microwave Door Handle?
Samsung Microwave Runs… [Issues & Solutions]