How To Reset A Whirlpool Oven [Detailed Guide]

If your Whirlpool oven is not functioning like it’s meant to, resetting it would be a good idea. In this article, we show you how to reset a Whirlpool oven and more.

How To Reset A Whirlpool Oven

Below are the steps you need to follow in order to reset your Whirlpool oven…

Step 1: Pull the oven away from the wall to access the power cord.

Step 2: Disconnect the power cord.

Step 3: Leave the oven unplugged for at least five minutes.

Step 4: Afterwards, plug the oven back in.

How To Reset A Whirlpool Oven After A Power Cut

Below, we show you how to reset a Whirlpool oven after a power cut…

Step 1: Locate the circuit breaker of your oven.

Step 2: Switch the breaker off.

Step 3: Leave the breaker off for 5 minutes in order to reset the oven.

Step 4: Switch the breaker back on.

Whirlpool Oven Control Reset

To reset your Whirlpool oven control, do the following…

Step 1: Unplug the oven’s power cord from the outlet or switch the breaker off.

Step 2: Leave the breaker off for a few minutes.

Step 3: After a few minutes, plug the oven back in or switch the circuit breaker back on.

Whirlpool Oven Clock Keeps Resetting — How To Fix

If your Whirlpool oven clock keeps resetting, the control board is faulty. The same also applies if your Whirlpool oven resets to 160 whenever you use it. If you would like to learn how to replace the control board in a Whirlpool range oven, read this article: Whirlpool Oven Control [Problems & Proven Solutions]. To replace the control board in a Whirlpool double wall oven, follow the steps listed below…

See also  Oven Won’t Turn On [Problems & Solutions]

Step 1: Switch the oven’s circuit breaker off.

Step 2: Open the two doors of your Whirlpool oven.

Step 3: Flip the locks on the hinges of the lower oven door forward.

Step 4: Close the door till it stops.

Step 5: Grip the sides of the door and lift it off.

Step 6: Set the door on a cloth lined surface.

Step 7: Do the same with the upper oven door.

Step 8: Remove the oven racks and set them aside.

Step 9: Using a Philips head screwdriver, take out the screws which hold the sides of the oven to the cabinet. There are two screws on each side.

Step 10: Take out the screws which hold the bottom vent of the oven in place.

Step 11: Pull the oven out of the cabinet with the help of an assistant and set it on a piece of cardboard.

Step 12: Take out the eight screws which hold the oven’s top front panel in place with a quarter inch nut driver.

Step 13: Set the panel aside.

Step 14: The board on the right is for the upper oven and the board on the left is for the lower oven. Note where each wire goes on the board you want to replace.

Step 15: Disconnect the wires from the board and take out the screws which hold it in place.

Step 16: Remove the board and get a replacement.

Step 17: Position the new board in the oven and hold it in place with the screws.

See also  Hotpoint Oven Keeps Turning Off [How To Fix]

Step 18: Reconnect the wires to the right places and return the oven’s top front panel.

Step 19: Secure the panel back to the oven with the eight screws and lift the oven back into the cabinet.

Step 20: Hold the sides of the oven to the cabinet with the four screws.

Step 21: Return the bottom vent and the screws that hold it in place.

Step 22: Lift the lower oven door and insert the hinges into the slots.

Step 23: Open the door fully and flip the hinge locks back.

Step 24: Do the same with the door of the upper oven.

Step 25: Slide the oven racks back in.

Step 26: Shut the oven doors.

Step 27: Switch the breaker back on.

The video below will show you how to replace the control board in a Whirlpool double wall oven.

Check out these articles…

Whirlpool Oven Error Codes [How To Fix]

Whirlpool Oven Smokes [How To Fix]

Whirlpool Stove Knobs [Problems & Proven Solutions]

Whirlpool Oven Fuse [How To, Problems & Solutions]

How To Calibrate A Whirlpool Oven [Detailed Guide]

Whirlpool Oven Thermostat [How To, Guide]

Whirlpool Oven Is Not Working [How To Fix]

Whirlpool Stove F9 Reset

To reset your Whirlpool stove when it shows the F9 error code, simply switch the breaker off for a few minutes. Switch the breaker back on after a few minutes. If that doesn’t fix the problem, there may be a problem with the circuit breaker. Contact an electrician to fix the problem.

How To Reset Whirlpool Oven Temperature

Resetting Whirlpool oven temperature or calibrating the temperature is done when the oven seems like it isn’t cooking at the set temperature. Calibrating a Whirlpool oven is a simple straightforward process. To reset your Whirlpool oven temperature, read this article: How To Calibrate A Whirlpool Oven [Detailed Guide]

How To Reset A Whirlpool Oven FAQ

Do Whirlpool Ovens Have Reset Buttons?

No, they don’t.

See also  Whirlpool Oven Lock [Problems & Proven Solutions]

Leave a Comment