Inglis Oven Control [How To, Issues & Proven Solutions]

If your Inglis oven control board is not working, you are in the right place. In this article, we will look at Inglis oven control problems and show you how to fix them.

Inglis Oven Control Board Not Working — How To Fix

If your Inglis oven control board is not working, it should be replaced. Below, we have listed the steps you need to follow in order to replace your Inglis oven control board…

Step 1: Before you start the repair, you will need to disconnect the oven’s power. To do this, pull the oven away from the wall.

Step 2: Unplug the cord from the outlet to disconnect the power.

Step 3: Get a Philips screwdriver.

Step 4: Go to the oven’s rear and take out the screws which hold the upper panel in place.

Step 5: Lift the upper panel and set it aside.

Step 6: Take a picture of the control board. This will help you remember where each wire goes on the control board.

Step 7: Disconnect the wire plugs from the control board.

Step 8: Take out the two screws which hold the control board to the control panel.

Step 9: Get a new Inglis oven control board.

Step 10: If the new board doesn’t come with an overlay, peel the overlay off the old control board. You can use a putty knife to do this.

See also  How to Make Meatballs in Oven [4 Delicious Recipes]

Step 11: Stick the overlay to the new control board.

Step 12: Position the new control board on the control panel.

Step 13: Hold the control board in place with the two screws.

Step 14: Use the picture you took for reference to ensure that each wire goes to the right place on the control board.

Step 15: Reposition the upper panel on the oven’s rear.

Step 16: Hold the upper panel in place with the Philips head screws.

Step 17: Plug the power cord back into the outlet.

Step 18: Return the oven to its usual position.

Watch the video below for a visual of how to replace your Inglis oven control board step by step.

Inglis Oven Control Panel Not Working — How To Fix

If your Inglis oven control panel is not working, you will need to replace the overlay. Below, we have listed the steps you need to follow in order to replace the overlay of your Inglis oven…

Step 1: Before you start the repair on your Inglis oven, disconnect the power. To do this, you will need to pull the oven away from the wall.

Step 2: Go to the oven’s rear and unplug the cord from the outlet.

Step 3: Next, get a Philips screwdriver.

Step 4: Use the Philips screwdriver to take out the screws which hold the upper panel on the oven’s rear.

Step 5: Lift the upper panel off the oven and set it aside.

Step 6: Note where each wire goes on control board by taking a picture.

See also  Gorenje Oven Element [How To, Issues & Solutions]

Step 7: Disconnect the wires from the control board.

Step 8: Take out the two screws which hold the board to the oven using the screwdriver.

Step 9: Get a putty knife and a heat gun.

Step 10: Move the heat gun over the overlay to melt the glue which helps it stick to the control board.

Step 11: Use the putty knife to pry off the overlay from the control board.

Step 12: Get a new overlay.

Step 13: Position the new overlay on your Inglis oven control board.

Step 14: Peel off the protective film from the overlay.

Step 15: Reposition the control board on the control panel and secure it using the screws.

Step 16: Connect the wires back to the control board. Use the picture you took for reference to ensure that each wire goes to the right place.

Step 17: Reposition the upper panel on the oven’s rear.

Step 18: Hold the panel in place with the Philips screws.

Step 19: Plug the oven’s power cord back into the outlet.

Step 20: Push the oven back to the wall.

Leave a Comment